Europe, Middle East and Africa
- Home
- > Services & Products
- > Semiconductor
- > Microcontrollers
- > 16-bit
- > MB96F313RSAPMC
MB96310 Series : MB96F313RSAPMC
Not recommended for new designsPlease see replacement part(s): |
MB96F313RSBPMC |
- Product Features
- Documentation
- Starterkits
- Debugger and Emulator
- Software Examples
- Application Notes
DESCRIPTION
MB96300 series is based on Fujitsu's advanced 16FX architecture (16-bit with instruction pipeline for RISC-like performance). The CPU uses the same instruction set as the established 16LX series - thus allowing for easy migration of 16LX Software to the new 16FX products. 16FX improvements compared to the previous generation include significantly improved performance - even at the same operation frequency, reduced power consumption and faster start-up time.
For highest processing speed at optimized power consumption an internal PLL can be selected to supply the CPU with up to 56MHz operation frequency from an external 4MHz resonator. The result is a minimum instruction cycle time of 17.8ns going together with excellent EMI behavior. An on-chip clock modulation circuit significantly reduces emission peaks in the frequency spectrum. The emitted power is minimised by the on-chip voltage regulator that reduces the internal CPU voltage. A flexible clock tree allows to select suitable operation frequencies for peripheral resources independent of the CPU speed.
BLOCK DIAGRAM
MB96F313RSAPMC - PRODUCT FEATURES
| CPU [Bits] | 16 |
| Package | FPT-48P-M26 |
| Pincount | 48 |
| Flash memory | 96.00 KByte |
| Flash Security (read protection) | yes |
| RAM (code & data) | 8.00 KByte |
| VCC min | 3.00 V |
| VCC max | 5.50 V |
| Min. Temperature | -40 °C |
| Max. Temperature | 125 °C |
| Max. CPU frequency | 56.00 MHz |
| Clock Supervisor | yes |
| DMA channels | 3 |
| Max. I/Os | 36 |
| A/D Converter | 1 |
| A/D channels | 12 |
| A/D resolution | 10 bit |
| A/D conversion time (min.) | 1.700 µs |
| LIN-USART | 3 |
| CAN | 1 |
| Programmable Pulse Generator (PPG) | 14 |
| IOTimer | 1 |
| Reload Timer | 4 |
| Timebase Timer (TBT) | 1 |
| Clock Timer | 1 |
| Real Time Clock (RTC) | yes |
| Watchdog | 1 |
| Low Voltage Detection (LVD) | yes |
| External IRQ | 11 |
| CAN Message Buffers | 32 |
MB96F313RSAPMC - DOCUMENTATION
| Datasheet | ds96310-ds07-13808-2e.pdf |
| Datasheet Errata | ds96310-ds07-13808-2et2.pdf |
| Hardware Manual | MB96300_HWM_rev16_20081107.pdf |
| Hardware Manual Errata | MB96300_HWM_rev16_20081107-errata-x1-02.pdf |
| Customer Information | CI-300010-E-V32-MB96300_List_of_functional_limitations.pdf |
| Customer Information | CI-300047-E-V10-Data_Polling_Flag_during_Flash_Sector_Erase.pdf |
| Customer Information | CI704-00002-1v0-E_Incorrect_Relocation_CKOT_20101217.pdf |
| Customer Information | CI704-00007-2v0-E_LIN_sysnc_mode_20101221.pdf |
| Customer Information | CI704-00008-1v0-E_C_CAN_INITduringTX_20101224.pdf |
| Customer Information | CI704-00009-1v0-E_P03_0_test_mode_activation.pdf |
| Package datasheet | fpt-48p-m26.pdf |
| Programming Manual | prog16fx-cm44-00203-3e.pdf |
| Errata Programming Manual | prog16fx-cm44-00203-3et1.pdf |
MB96F313RSAPMC - STARTERKITS
| Starterkit | SK-16FX-48PMC |
| Power Supply Unit for Starterkit | POWERED BY USB |
| Starterkit | SK-96310-48PMC |
| Power Supply Unit for Starterkit | PSU_SNG12-24W |
MB96F313RSAPMC - DEBUGGER and EMULATOR
| Monitor Debugger | euroscope |
| EVA-Chip EVA-Chip | MB96V300CRB-ES |
| Emulation Main Unit | MB2198-01-E |
| Emulation Pod/Adapter | MB2198-500-E |
| Probe Cable | MB2198-509-E |
| Socket | NQPACK048SD, HQPACK048SD |
| Accessory Kit | ACCESSORIES16FX |
| Starterkit | SK-96310-48PMC |
| Power Supply Unit for Starterkit | PSU_SNG12-24W |
| Starterkit | SK-16FX-48PMC |
| Power Supply Unit for Starterkit | POWERED BY USB |
MB96F313RSAPMC - SOFTWARE EXAMPLES
The following software is for demonstration purposes only. It is not fully tested, nor validated in order to fulfill its task under all circumstances. Therefore, this software or any part of it must only be used in an evaluation laboratory environment.
Use only the template-project as starting point for your application. Only the template-project will be updated in case of any change of the header files, startup code etc.!
| Device specific Software Examples | |
| Template project for MB96313as | 96310_template_96313as-v17.zip |
| Template project for MB96313aw | 96310_template_96313aw-v17.zip |
| Template project for MB96313rs | 96310_template_96313rs-v17.zip |
| Template project for MB96313rw | 96310_template_96313rw-v17.zip |
| Template project for MB96315as | 96310_template_96315as-v17.zip |
| Template project for MB96315aw | 96310_template_96315aw-v17.zip |
| Template project for MB96315rs | 96310_template_96315rs-v20.zip |
| Template project for MB96315rs | 96310_template_96315rw-v20.zip |
| UART2 communication demonstration project | 96310_uart2_async-v10.zip |
All software examples
APPLICATION NOTES
Please find a selection of Application Notes here or check the complete overview:
| Shows the differences to be aware of when migrating from a 16LX project to the 16FX | mcu-an-300026-e-v17 |
| How to use IO-Ports | mcu-an-300200-e-v14 |
| How to use PPG | mcu-an-300201-e-v16 |
| Basic functionality of the Reload Timer | mcu-an-300202-e-v13 |
| How to use External Interrupts | mcu-an-300203-e-v17 |
| How to use the IOTimer: FR-Timer, ICU, OCU | mcu-an-300204-e-v15 |
| How to use the LIN-USART | mcu-an-300205-e-v17 |
| How to use the Watchdog Timer | mcu-an-300206-e-v13 |
| How to use the Real Time Clock | mcu-an-300207-e-v13 |
| How to set up the external bus interface | mcu-an-300208-e-v16 |
| How to use Interrupts | mcu-an-300210-e-v15 |
| How to use the Delayed Interrupt | mcu-an-300211-e-v12 |
| This Application Note describes the function and usage of the Flash Security feature of the 16FX Family | mcu-an-300213-e-v15 |
| Functionality of the Clock-Output | mcu-an-300214-e-v12 |
| Functionality of the ADC | mcu-an-300215-e-v12 |
| Explanation of 16FX (MB96300) Flash Memory | mcu-an-300218-e-v15 |
| 16FX MB96300 Series Boot ROM Protocol and MCU serial Flash Programming | mcu-an-300224-e-v21 |
| Functionality of the ROM Mirror | mcu-an-300212-e-v11 |
| Installation of MB2198-01 based emulation system | mcu-an-300209-e-v10 |
| Source Clock Timers of MB96300 Series | mcu-an-300216-e-v12 |
| Getting started with MB2198-01 based emulation system and Softune | mcu-an-300217-e-v10 |
| Reset considerations and causes | mcu-an-300219-e-v12 |
| Usage and settings of DMA | mcu-an-300220-e-v14 |
| Explanation of Memory Patch Function | mcu-an-300221-e-v12 |
| Explanation of the Alarm Comparator | mcu-an-300222-e-v12 |
| Recommendations for 16FX hardware setup | mcu-an-300223-e-v14 |
| 16FX-MCU-Clocks and Clock Tree configuration | mcu-an-300225-e-v14 |
| Standby and low power modes | mcu-an-300226-e-v15 |
| Usage of CAN interface | mcu-an-300228-e-v15 |
| How to use the Clock Calibration Unit | mcu-an-300229-e-v13 |
| How to get started with a 16FX project in Softune | mcu-an-300233-e-v11 |
| Explanation of the 16FX emulation system features | mcu-an-300240-e-v13 |
| How to drive a SD/MMCard over a SPI interface. | mcu-an-300245-e-v11 |
| 16FX performance explanations | mcu-an-300244-e-v10 |
| A lamp is controlled by PPG and monitored via ADC | mcu-an-300237-e-v11 |
| Connect a matrix keypad | mcu-an-300238-e-v12 |
| Generation of additional software PWM channel at IO ports using a reload timer and DMA transfer | mcu-an-300239-e-v11 |
| 16FX Start-Up File | mcu-an-300241-e-v11 |
| How to calculate CRC16 or a simple Checksum for Flash memory and check it during runtime | mcu-an-300253-e-v20Attachment |
| Description of the most common SPI formats and how to implement them on Fujitsu 16-bit MCUs. | mcu-an-300002-e-v13 |
| This application note provides some information and recommendations how to connect external crystals or resonators to Fujitsu microcontrollers. In order to achieve a proper and stable clock oscillation the composition of external circuits, PCB layout design and the microcontroller must be taken into account and evaluated carefully | mcu-an-300007-e-v13 |
| This application note shows some possibilies to drive a BLDC motor with different MCUs using a single PPG. | mcu-an-300020-e-v10Attachment |
| This application note describes how to use the Fujitsu's LIN USART to control LIN devices (e.g.: AMIS-30621 stepper motor driver). | mcu-an-300037-e-v11Attachment |
| This application note describes how to use the Fujitsu's Softune with EasyCode | mcu-an-300038-e-v10 |
| Customer information to inform about LIN conformance tests | mcu-an-300106-e-v11 |
| This Application Note describes how to set up Eclipse | mcu-an-300113-e-v10 |
All application notes