MB95150 Series : MB95F156JPMC
- Product Features
- Documentation
- Starterkits
- Debugger and Emulator
- (FLASH-)ROM Programming Tools
- Software Examples
- Application Notes
SERIES KEY FEATURES
LIN, LCD (4x16)
DESCRIPTION
The Trumpet series is the most compact series of the F2MC*-8FX family with on chip LCD controller, capable to address 64 segments (16 seg x 4 com). Designed as a general purpose device, the MB95150 series offers a wide range of additional internal peripherals, including Programmable Pulse Generators, I/O Timers, A/D Converter, SIO and LIN-USART. The fast processing and low power consumption of the 8FX CPU core benefits wide application areas - appliances, consumer, industrial.
BLOCK DIAGRAM
MB95F156JPMC - PRODUCT FEATURES
| CPU [Bits] | 8 |
| Package | FPT-52P-M01 |
| Pincount | 52 |
| Flash memory | 32.00 KByte |
| Flash Security (read protection) | yes |
| RAM (code & data) | 1.00 KByte |
| VCC min | 2.88 V |
| VCC max | 5.50 V |
| Min. Temperature | -40 °C |
| Max. Temperature | 85 °C |
| Max. CPU frequency | 16.25 MHz |
| Subclock | yes |
| Clock Supervisor | yes |
| Max. I/Os | 39 |
| A/D Converter | 1 |
| A/D channels | 8 |
| A/D resolution | 10 bit |
| A/D conversion time (min.) | 1.200 µs |
| LCD | 64 |
| UART | 1 |
| LIN-USART | 1 |
| SIO (Serial I/O) | 1 |
| Programmable Pulse Generator (PPG) | 2 |
| Pulse Width Modulator (PWM) | 1 |
| Timer Counter | 2 |
| Timebase Timer (TBT) | 1 |
| Watchdog | 1 |
| Low Voltage Detection (LVD) | yes |
| External IRQ | 8 |
MB95F156JPMC - DOCUMENTATION
| Datasheet | ds95150m-ds07-12613-4e.pdf |
| Hardware Manual | hm95150m-cm26-10110-4e.pdf |
| Hardware Manual Correction | hm95150m-cm26-10110-4et4.pdf |
| Package datasheet | fpt-52p-m01.pdf |
| Programming Manual | prog8fx-cm26-00301-2e.pdf |
MB95F156JPMC - STARTERKITS
| Starterkit | MB2146-401 |
| Starterkit Adapter | MB2146-303A-E |
| Package Conversion Adapter | MB2146-261 |
MB95F156JPMC - DEBUGGER and EMULATOR
| EVA-Chip EVA-Chip | MB95FV100D-103PBT |
| Emulation Main Unit | MB2146-09A-E |
| Emulation Pod/Adapter | 0 |
| Probe Cable | 0 |
| Accessory Kit | ACCESSORIES8FX |
| Starterkit | MB2146-401 |
| Package Conversion Adapter | MB2146-261 |
| Starterkit Adapter | MB2146-303A-E |
| Power Supply Unit for Starterkit | INCLUDED |
MB95F156JPMC - (FLASH-)ROM PROGRAMMING TOOLS
| Name | Type | Adapter |
| FLASH_PROGRAMMER_8FX | serial (async) |
MB95F156JPMC - SOFTWARE EXAMPLES
The following software is for demonstration purposes only. It is not fully tested, nor validated in order to fulfill its task under all circumstances. Therefore, this software or any part of it must only be used in an evaluation laboratory environment.
| This is a project template for the 8FX Series (Trumpet - MB95F156) | 95150_template_trumpet_mb95f156-v11.zip |
All software examples
MB95F156JPMC - APPLICATION NOTES
Please find a selection of Application Notes here or check the complete overview:
| This appnote for the 8L Family gives hints to optimize the EMI performance. | mcu-an-389024-e-v11 |
| This document describes how to set up a new project for the 8FX Family. | mcu-an-395001-e-v11 |
| This application note describes how to program the Flash device MB951xx in serial async mode. | mcu-an-395003-e-v13 |
| How to use the Softune Workbench Monitor Debugger for 8FX. | mcu-an-300049-e-v10 |
| This application note describes how to program the Flash device MB951xx in serial sync mode by use of MB2146-09. | mcu-an-300050-e-v10 |
| This installation guide will help you set up the MB2146-09 BGM adapter with the MB2146-301 or MB2146-303 MCU board for Fujitsu 8FX microcontroller and its usage with 8-bit Softune Workbench V30L29 or higher. | mcu-an-395002-e-v10 |
| This application note gives a rough overview about how LCD displays work and illuminates different methods to control a LCD by a microcontroller. | mcu-an-300001-e-v13 |
| This application note describes the most common SPI formats and how to implement them on Fujitsu 16-bit MCUs. | mcu-an-300002-e-v12 |
| This application note provides some information and recommendations how to connect external crystals or resonators to Fujitsu microcontrollers. In order to achieve a proper and stable clock oscillation the composition of external circuits, PCB layout design and the microcontroller must be taken into account and evaluated carefully | mcu-an-300007-e-v13 |
| This application note shows some possibilies to drive a BLDC motor with different MCUs using a single PPG. | mcu-an-300020-e-v10 Attachment |
| This application note describes how to use the Fujitsu’s LIN USART to control LIN devices (e.g.: AMIS-30621 stepper motor driver). | mcu-an-300037-e-v11 Attachment |
| customer information to inform about LIN conformance tests | mcu-an-300106-e-v10 |
| This Application Note describes how to setup the Softune Workbench to automatically start the debugger at start. | mcu-an-300097-e-v11 |
All application notes
