MB91301 Series : MB91302APFF
Product number changed
|
|
- Product Features
- Documentation
- Starterkits
- Debugger and Emulator
- Software Examples
- Application Notes
SERIES KEY FEATURES
Low cost
DESCRIPTION
The MB91302A microcontroller incorporates a variety of IO resources and an external interface for embedded control applications that require the processing power of a high-performance, fast CPU as well as a SDRAM interface that allows the direct connection of SDRAM to the chip.
BLOCK DIAGRAM
MB91302APFF - PRODUCT FEATURES
| CPU [Bits] | 32 |
| Package | FPT-144P-M12 |
| Pincount | 144 |
| RAM (code & data) | 4.00 KByte |
| Data RAM | 4.00 KByte |
| Instruction Cache | 4.00 KByte |
| VCC min | 3.00 V |
| VCC max | 3.60 V |
| Min. Temperature | 0 °C |
| Max. Temperature | 70 °C |
| Max. CPU frequency | 68.00 MHz |
| Max. I/Os | 80 |
| A/D Converter | 1 |
| A/D channels | 4 |
| A/D resolution | 10 bit |
| UART | 3 |
| I2C | 2 |
| Programmable Pulse Generator (PPG) | 4 |
| Input Capture Unit (ICU) | 4 |
| IOTimer | 1 |
| Reload Timer | 3 |
| Timebase Timer (TBT) | 1 |
| Watchdog | 1 |
| External Bus | yes |
| External Bus mode | Non-Multiplexed |
| SDRAM interface | yes |
| Chip-Selects | 8 |
| External IRQ | 8 |
MB91302APFF - DOCUMENTATION
| Datasheet | ds91301-ds07-16502-4e.pdf |
| Hardware Manual | hm91301-cm71-10114-4e.pdf |
| Hardware Manual Correction | hm91301-cm71-10114-4et3.pdf |
| Package datasheet | fpt-144p-m12.pdf |
| Instruction Manual | progfr-cm71-00101-5e.pdf |
MB91302APFF - STARTERKITS
| Starterkit | MB91914EB |
| Starterkit | StarterkitMB91302 |
MB91302APFF - DEBUGGER and EMULATOR
| EVA-Chip EVA-Chip | MB91V301ACR-ES |
| Emulation Main Unit | MB2198-01-E |
| DSU Cable | MB2198-10-E |
| Emulation Pod/Adapter | MB2198-100-E |
| Probe Cable | MB2198-101-E |
| Socket | NQPACK144SE, HQPACK144SE |
| Accessory Kit | ACCESSORIES32 |
| Starterkit | StarterkitMB91302 |
| Power Supply Unit for Starterkit | INCLUDED |
| EVA-Chip EVA-Chip | MB91V301ACR-ES |
| Emulation Main Unit | MB2198-01-E |
| DSU Cable | MB2198-10-E |
| Emulation Pod/Adapter | MB2198-100-E |
| Option | MB2198-90 |
| Probe Cable | MB2198-101 |
| Socket | NQPACK144SE, HQPACK144SE |
| Accessory Kit | ACCESSORIES32 |
| Starterkit | MB91914EB |
| Power Supply Unit for Starterkit | INCLUDED |
MB91302APFF - SOFTWARE EXAMPLES
The following software is for demonstration purposes only. It is not fully tested, nor validated in order to fulfill its task under all circumstances. Therefore, this software or any part of it must only be used in an evaluation laboratory environment.
| This is a project template for the MB91302 Series. | 91302_template-v12.zip |
| This project initializes the ADC Channel 0, Single-mode, acivation by software. The result is output via UART1. | 91302_adc_irq-v11.zip |
| This example performs a RAM test on the external SDRAM and outputs corrsponding error messages on UART1 in case of errors. | 91302_extbus_flash_sdram_memorytest_full-v11.zip |
| This example performs a small RAM/Flash test on the external SDRAM and Flash memory | 91302_extbus_flash_sdram_memorytest_short-v14.zip |
| This project runs on Starterkit91302 with the Jasmine graphic controller sub-board. It simply draws a rectangle and circle on the screen. | 91302_extbus_gdc_jasmine-v10.zip |
| This project runs on Starterkit91302 with the Jasmine graphic controller sub-board. As an example it shows an industrial graphic for process control. | 91302_extbus_gdc_jasmine_industrial-v10.zip |
| The program performs a read/write access to an I2C-bus EEPROM (Microchip 24LC08B). | 91302_i2c-v10.zip |
| The program performs a read/write access to an I2C-bus EEPROM (Microchip 24LC08B). Single Byte read/write is done by using IRQs. | 91302_i2c_irq-v10.zip |
| This is an example project for external interrupts. | 91302_irq_ext-v10.zip |
| This debugger has been modified to be used on the Starterkit91302. For this reason special settings have been done and must be considered in case of any modifications. | 91302_mondeb_15mhz-v12.zip |
| This project initializes PPG ch0. PWM mode, activated by Software trigger, IRQ enabled (activated by duty cycle). | 91302_ppg_irq-v11.zip |
| This project initializes PPG ch0-3 for synchronous start. PWM mode, activated by Software trigger, rising egde for trigger detection, IRQ enabled. | 91302_ppg_syncstart-v11.zip |
| The reload project initializes Reload Timer 0 and 1. In the ISR, port G (bit 6 or 7) are toggled | 91302_rlt_irq-v11.zip |
| The example generates a running light on the 8 user LEDs D1-D10 on the Starterkit91302. | 91302_starterkitmb91302-v10.zip |
| This simple test project shows conversion of binary values to ASCII and allows to display binary values in Hex or Dec values on the terminal output. | 91302_sw_bin_dec_hex-v10.zip |
| This example does a simple string output on UART0 and UART1 to test their function. | 91302_uart_async-v16.zip |
| This example uses UART1 with IRQs to transmit and receive data in asynchronous mode. | 91302_uart_async_irq-v10.zip |
All software examples
MB91302APFF - APPLICATION NOTES
Please find a selection of Application Notes here or check the complete overview:
| This application note will help you how to debug the application with Softune Workbench V6 Simulator. The simulator debugger simulates the MCU operations (executing instructions, memory space, I/O ports, interrupts, reset, etc.) with software to evaluate a program. | mcu-an-300103-e-v10 |
| This application note shows some possibilies to drive a BLDC motor with different MCUs using a single PPG. | mcu-an-300020-e-v10 Attachment |
| This Application Note describes how to setup the Softune Workbench to automatically start the debugger at start. | mcu-an-300097-e-v11 |
All application notes
