MB90420 Series : MB90F423GBPF
- Product Features
- Documentation
- Starterkits
- Debugger and Emulator
- (FLASH-)ROM Programming Tools
- Software Examples
- Application Notes
SERIES KEY FEATURES
CAN, LCD (4x24), Stepper Motor Driver (4ch)
DESCRIPTION
The instruction set retains the same AT architecture as the FUJITSU original F²MC-8L and F²MC-16L series, with further refinements including high-level language instructions, expanded addressing mode, enhanced (signed) multipler-divider computation and bit processing. In addition, A 32-bit accumulator is built in to enable long word processing.
BLOCK DIAGRAM
MB90F423GBPF - PRODUCT FEATURES
| CPU [Bits] | 16 |
| Package | FPT-100P-M06 |
| Pincount | 100 |
| Flash memory | 128.00 KByte |
| RAM (code & data) | 6.00 KByte |
| VCC min | 3.70 V |
| VCC max | 5.50 V |
| Min. Temperature | -40 °C |
| Max. Temperature | 105 °C |
| Max. CPU frequency | 16.00 MHz |
| Subclock | yes |
| Max. I/Os | 58 |
| A/D Converter | 1 |
| A/D channels | 8 |
| A/D resolution | 10 bit |
| Sound Generator (SG) | 1 |
| LCD | 96 |
| Stepper Motor Control (SMC) | 4 |
| UART | 2 |
| CAN | 2 |
| Programmable Pulse Generator (PPG) | 6 |
| Input Capture Unit (ICU) | 4 |
| IOTimer | 1 |
| Reload Timer | 2 |
| Timebase Timer (TBT) | 1 |
| Clock Timer | 1 |
| Real Time Clock (RTC) | yes |
| Watchdog | 1 |
| CPU Operation Detection | yes |
| External IRQ | 8 |
MB90F423GBPF - DOCUMENTATION
| Datasheet | ds90420-5-ds07-13711-5e.pdf |
| Hardware Manual | hm90420_5-cm44-10113-4e.pdf |
| Hardware Manual Correction | hm90420_5-cm44-10113-4et1.pdf |
| Customer Information | standby_cancel_fail_03dec02_finalj2.0e1.0.pdf |
| Package datasheet | fpt-100p-m06.pdf |
| Programming Manual | prog16lx-cm44-00201-3e.pdf |
MB90F423GBPF - STARTERKITS
| Starterkit | Flash-CAN-100P-M06 |
MB90F423GBPF - DEBUGGER and EMULATOR
| EVA-Chip EVA-Chip | MB90V420GCR-ES |
| Emulation Main Unit | MB2147-01-E |
| Emulation Pod/Adapter | MB2147-10 |
| Probe Cable | MB2132-457 |
| Socket | IC149-100-014-B5,IC149-100-114-B5,IC149-100-014-S5,IC149-100-114-S5 |
| Accessory Kit | ACCESSORIES16 |
| Starterkit | Flash-CAN-100P-M06 |
| Power Supply Unit for Starterkit | PSU_SNG12-24W |
MB90F423GBPF - (FLASH-)ROM PROGRAMMING TOOLS
| Name | Type | Adapter |
| FLASH_PROGRAMMER_16LX | serial (async) | |
| CONITEC GALEP | serial | Conitec 210865/210915 |
| FUJITSU FLASHKIT | serial (async/sync) |
MB90F423GBPF - SOFTWARE EXAMPLES
The following software is for demonstration purposes only. It is not fully tested, nor validated in order to fulfill its task under all circumstances. Therefore, this software or any part of it must only be used in an evaluation laboratory environment.
| Project template for MB90420 Series | 90420_template-v13.zip |
| Project template for the MB90425 Series | 90425_template-v16.zip |
| CAN0 and CAN1 will send out a counter value. | 90420_can-v11.zip |
| An internal variable is decremented and put out to port P4 | 90420_io-v10.zip |
| This demo will sample all 8 A/D-channels in continuous mode | 90425_adc_irq-v12.zip |
| This demo will sample all 8 A/D-Channels and send the results via UART1 | 90425_adc_uart1_async-v12.zip |
| CAN0 will work as a simple repeater. | 90425_can-v11.zip |
| An internal variable is decremented, and at zero, clock mode is toggled. | 90425_clk_sub-v11.zip |
| The Input Capture Unit 1 is used for time measurement on Port IN0 (Pin98) | 90425_frt_icu-v11.zip |
| An internal variable is decremented and put out to port P4 (LEDs on FLASH-CAN-100P) | 90425_io-v11.zip |
| A falling edge on INT0..INT7 will toggle PDR4_P40..7 (LEDS on FLASH-CAN-100P) | 90425_irq_ext-v11.zip |
| The internal LCD controller and internal resistor devider are used, different methods to switch segments are shown. | 90425_lcd_seg-v10.zip |
| This project uses PPG channels 0-2 to put out a rectangular wave. | 90425_ppg-v11.zip |
| Interrupts of Reload Timers 0 and 1 toggle LEDs on Port 4 | 90425_rlt_irq-v11.zip |
| A welcome string is sent via UART0, and every received character is echoed. | 90425_uart0_async-v11.zip |
| A welcome string is sent via UART1, and every received character is echoed. | 90425_uart1_async-v10.zip |
| The Real-Time Watch Timer is set to 00:00:06 (h/m/s). Each second an interrupt occurs. | 90425_wt-v11.zip |
All software examples
MB90F423GBPF - APPLICATION NOTES
Please find a selection of Application Notes here or check the complete overview:
| This is a short documentation to give an introduction how to start a project with the Softune Workbench. | mcu-an-390025-e-v23 |
| This application note explains the different possibilities to program the Flash MCUs. | mcu-an-390031-e-v26 |
| This application note describes the commands which are supported by the BiROM of the 16LX Flash MCUs in order to generate an own programming environment. | mcu-an-390027-e-v28 |
| This application note roughly shows the necessary steps for transition to standby-mode and wake-up for 16LX Family MCUs. | mcu-an-390058-e-v21 |
| How to set up a hardware environment for 16LX Family MCUs. | mcu-an-390098-e-v20 |
| This appnote for the 16LX Family gives hints to optimize the EMI performance. | mcu-an-390053-e-v14 |
| This application note gives a rough overview about the embedded A/D converter used within the 16LX Series and reflects the different modes that can be used. | mcu-an-390084-e-v14 Attachment |
| This installation guide will help you to quickly start setting up the MB2147-01 emulation hardware for Fujitsu 16-bit MCUs. | mcu-an-390070-e-v29 |
| First steps how to use the Emulator MB2147-01 together with the Softune Workbench V30L28 or higher using an evaluation MCU with its Starter Kit. | mcu-an-390069-e-v13 |
| This document describes the debugging methods of a MB90V340 system together with a FLASH-CAN-100P-340 target board. | mcu-an-390083-e-v20 |
| Recommendation for MODE-Pins in case of external noise | mcu-an-390093-e-v16 |
| This application note gives a rough overview about how LCD displays work and illuminates different methods to control a LCD by a microcontroller. | mcu-an-300001-e-v13 |
All application notes
